Job Description

• Installing, maintaining, and repairing electrical control, wiring, and lighting systems.
• Performing general electrical maintenance.
• Inspecting electrical components.
• Disassembles, inspects, reassembles, troubleshoots, repairs, and replaces malfunctioning parts or equipment (motors, switches, sensors, input/ output boards, controllers servos, gears, sprockets chains, knives, etc. using test equipment
• Troubleshooting electrical issues using appropriate testing devices.
• Repairing and replacing equipment, electrical wiring, and fixtures.
• Following National Electrical Code state and local building regulations.

Package offered: Rs. 1.64 LPA

Job Description

• Ensure that the machines are operating at optimum production.
• Ensure the following and coordinate with the fitter whenever required:
  • There is no chipping
  • There is no taper turning
  • The needles are making proper holes
  • The buttons are of the same thickness
  • The shape is coming as desired
• Ensure that there is a minimum stop time
• Take corrective action if the machine is stopped by coordinating with the fitter
• Ensure that the buttons are not being processed on the back side
• Ensure that the photocell is working fine and remove the powder as and when accumulated
• Refill blanks when empty
• Quality first
• The machine should not run empty for any reason

Job Description

• Perfect shape
• 1-4 complete, check for thickness
• Feeding
• Photocell
• Dropping/ Suction
• Tool holder complete with stopper in the right place
• No blank/button flying
• Clipping
• Hole distance
• Special instruction for tool design
• Measure Speed
• Set Proximity
• Set Thickness gauge
• Put Proper Slip

Job Description

• Maintain minimum wastage
  • Any wastage in any form needs to be collected on a regular basis if the same happens on the machine, thereby coming to know which machine gives us more problem and one can solve it.
• Informing the casting head if any blanks are getting over of the same order.
• Planning machining prog based on urgency.
  • As per the blanking report
  • Preparing for the next setting
• Preventive Maintenance– To see if any particular machine requires maintenance.
  • Based on sound, the persistently same problem faced by the same machine
  • Maintaining a report of consumables going into the individual machine in the department along with quantity and date.
• Maintain Minimum wastage
  • If wastage is above a particular limit inform the office, so if additional casting needs to be given it can be (based on the order)
• QC of buttons- whether it is made properly with respect to quality.
  • By inspection of design and thickness
• To maintain production reports of individual buttons/ blanks, which will be forwarded to the following dept.

Job Description

• Maintaining stock of Raw-Material and reporting about the low stock. Different RM have different reporting times- Calculating each and every raw material requirement
  • Filling out report weekly based on the stock available
• Testing of RM as when a batch comes and noting down in the tests in a book
  • Eg. Resin- Gel time, viscosity, Colour, Gravity
• Informing in office if any variation in RM quality apart from acceptable quality by providing the report
• Maintaining Minimum wastage
  • Being on the floor and explaining to the workers how work needs to be carried out
    • Raw-Material Wastage- Minimum quantity falls on the floor, cleaning the RM leftovers from the packaging drum/ vessel
    • Sheet breakage wastage- Removing the sheet not too soft, and cleaning the sheet drum properly so that there are no foreign particles in the drum
    • Punching wastage- Proper alignment of the punching belt and aligner with respect to the sheet
• Planning casting prog based on urgency as well as reducing worker load
  • Calculate colour
  • Checking colour shade
  • Writing down the casting weights, size, colour thickness and article number and giving them to the weigher of RM.
  • If any program is marked urgent, it needs to be casted first.
  • Multi-layer casting reduces the blanks output, so if there is a shortage of blanks in the machining dept. (The mcing dept. head will inform) producing such blanks by which the machines running do not have a stop time.
• To maintain a report of production
  • To maintain production reports of individual blanks, which will be forwarded to the following dept.
    • If wastage is high, do additional casting for the same
• QC of blanks– whether it is made properly with respect to quality and quantity.
  • Above report for quantity
  • Quality– random check of sheets from all drums for thickness and disbursement of pigments and pearl.
• If any maintenance is required, get it done
  • Inform maintenance personnel for the same
  • Maintaining reports of consumables going into individual machines in the department along with quantity and date
• To instruct M/cing dept. If any particular instruction is given.
  • To write in the blanking report
• Handling workers in dept and if problem report to the office
  • If any problems are faced by the workers related to work or amongst themselves, one needs to report to the office.

Job Description

• Check sheet/ gross
• Thickness
• Proper marking on slips
• Production rounds
• Wastage
• Mark slips
• Dryer Rounds
• Dryer Wastage
• Proper slips
• To maintain production reports of individual blanks, which will be forwarded to the following dept.
• Distributing the same on machines or stocking the same

Job Description

• Perfect weighting
• Perfect MEKP & Mixing
• Proper Pouring
• Properly emptying the container
• Filtration
• Clean vessels
• Sheet cutting straight
• No sheet breakage in removing or putting on the floor
• Perfect punching
• CenteringDistance
• Jali should not break
• No taper blanks
• Proper chalni

Job Description

• Making report of machining dept.- wt. of buttons made in the shift/ speed of machines
• To check whether the Machining of buttons is proper
• Mixing of buttons based on the quality of machining for polishing
• Deciding the weight of quartz power to put in drums
  • If buttons are rough lesser quantity needs to be loaded, and more quartz powder d=needs to be added in the drum for polishing
• Checking the right weight of ceramic media in drums and getting it topped up on a regular basis
• Getting maintenance done
• Getting the buttons removed from drums with a proper polish
• To maintain the production report of individual button/ buttons, which will be forwarded to the following dept.

Job Description

• Maintaining store inventory of consumables
• Maintaining report of stock used in individual machinery
  • Thereby knowing which machine is using more consumables from which we come to know whether a particular machine requires maintenance or not
• Informing the Maintenance dept of the breakdown of machinery if the same parts are being used again and again thereby reducing further breakdown as well as usage of consumables
• Informing purchase dept/ office about consumables required.

Job Description

• ​Check the quality/ polish of products
• Weigh and distribute products for checking
• Get the products packed appropriately
• Make sure to pack in the right packet
• Count the right no. of packets in the bag
• Write down the right item in the bag
• Prepare dispatch slip
• Coordinate Dispatch
• Supervise Checking, Packing & Dispatch
• Update report sheet once products are received
• Update report sheet once products are under checking & Packing
• Update report sheet once products are packed
• Maintain report of items in stock

Job Description

• Production
• Production planning based on orders/stock required
• Tabulating production reports
• Production planning for Casting dept./ machining dept. based on goods required and urgency of the order
• Despatch
• Dispatching of goods based on order
• Accounts

Job Description

• Must reach 10 minutes before duty time so that they can change, go to the bathroom, drink water etc. Must be at a duty station at duty hour. Same applies at lunchtime (30 mins. From leaving the machine to join the machine)
• Cannot leave machine during Evening/ Lunchtime until reliever comes to the machine
• To wear Earplugs/ Masks Compulsorily
• No throwing wrappers etc, no spitting on the floor, To use dustbins.
• Bathroom/ Water etc only once every two hours
• Must be at work station and not found huddled together or at the window/ in another department or elsewhere.
• Proper marking of slips

Job Description

• Ensure dryers are emptied fully every time.
• Drying blanks and buttons and getting them distributed based on the requirement
• For inspection weighing each button item along with making gross to make sure the right quantity has been sent and received after packing
• No mixing of buttons and blanks/ two different types of buttons